Step Instruction for Bathtub Installation
Step Instruction for Bathtub Installation
Blog Article
Are you currently trying to locate resources about A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't precisely brain surgery, however it does need solid plumbing, carpentry, and also sometimes, tiling abilities. Changing an old bath tub with a new one is also a moderately tough job. If the old tub is conveniently easily accessible, the job can move rapidly; if you need to open a wall surface to eliminate the old tub and also place the new bath tub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will need a helper to move out the old tub and embeded in the new one. Make sure you have actually qualified on your own for the job and also fit attempting it. Instead of working with a service provider to take over a halfway-completed job, it is far better to think about employing one prior to you start. Possibilities are you may need a specialist plumber to make tube connections.
This article will certainly help you set up a brand-new bathtub in your restroom if you have actually already bought a new bathtub and also don't need to alter the arrangement of your previous supply of water pipelines.
Your tools and product checklist must consist of the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you need to do is disconnect the water system. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing faucets can be fairly bothersome as a result of the limited gain access to that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the remaining water that will originate from the pipes. Once the supply pipelines have actually been eliminated, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Before going on to fit the brand-new taps, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in location between the tap and also the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet connectors. The previous type must be attached to the faucet ends first, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Using the two wood boards under its feet, place the bathtub in the called for position. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small factors.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the bath tub up until the level checks out level.
To mount faucets, fit the bottom of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Activate the water system and examine all joints and new pipework for leaks and tighten them if needed. Fill up the bathtub and also check the overflow electrical outlet and also the typical electrical outlet for leakages.
Ultimately, repair the bath paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bath tub ought to wait up until the tub has been made use of a minimum of when as this will certainly settle it into its last setting.
Preparing for the Setup
First of all, the sustaining structure supplied with the bath needs to be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the tap includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to stop stress on the bath tub.
Fit the adaptable tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you make use of all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last position.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to break a stiff seal, creating the water to pass through the wall between the bath and also the tiling, leading to problems with moisture and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bathtub with water before securing, to permit the movement experienced when the bathtub is in usage. The sealant can split fairly early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily offered on the market. It is advisable to fit the tiles using water-resistant or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that report on How to Install a Bathtub Yourself through an associate on a different web page. You should take the opportunity to distribute this write-up if you appreciated it. Thank-you for going through it.
Excellence in emergency plumbing services. Report this page